A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
Why is my hot tub control panel not working?
If the control panel is frozen or deceased, you have to check if the problem is the control panel or the circuit board. Examine if there is moisture in the display. Check if there are cracked buttons or if a part is wet. If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board.
How do you reset a spa controller?
To Reset the SP400/600/601 and Xcelsior Spa Pool System wait a minimum of 20 minutes to allow the heater tube/area to cool. Then press the down, up and pump buttons all simultaneously and hold for 3 seconds. To Reset the SP800 & SP1200 wait a minimum of 20 minutes to allow the heater tube to cool.
How do I know if my hot tub circuit board is bad?
If you DO have 220 volts across both hot wires coming from the house, then next measure the voltage across both heating element pins. You should see 220 volts. If you do not, then the circuit board is faulty and will need to be replaced or sent to us for repair.
How do you troubleshoot a hot tub circuit board?
If you have no display on your topside control panel, check the cable for damage, following it right to where it plugs in, on the circuit board. Unplug it from the board and the low-speed pump will come on within 1 minute, on both systems. If that doesn’t happen, either the pump or the circuit board is bad.
How do I unlock my hot tub controls?
How do you unlock the Sundance spa control panel?
Press DISPLAY, MODE and (down) button within 3 seconds to unlock panel.
How do you override a hot tub temperature control?
How do I unlock my Marquis spa control panel?
Panel Lock Press TEMP+ or TEMP- pad followed by QUIET SOAK pad to lock. Then press TEMP+ or TEMP- pad followed by QUIET SOAK pad to unlock.
How do I drain my hot tub everyday?
How do I replace the heating element in my hot tub?
What does Dr code on hot tub mean?
Low Water Errors
Common Error Codes: DR, DY, DRY, H20. Low water errors are meant to indicate a lack of water in the hot tub pump. These errors are usually a sign that there is not enough water in the hot tub, although they will also display if there is air trapped in the pump (an “air lock”).
How do I fix the HH code on my hot tub?
Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. For OH, HH or HOT trouble codes, an overheating hot tub is not usually a heater problem. It is almost always a flow problem.
How do you fix the error code on a hot tub?
DR or DRY Error Message
This error message is similar to the FLO error message. Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.
How do I know if my hot tub has an airlock?
As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.
Will an airlock clear itself?
In a well designed low pressure water pipe system, air should clear naturally even if you run out of water. As the pipe system fills again, the air should naturally rise to the top and be expelled. Air locks happen when the pipe system is not well designed.
How do you get air out of hot tub pipes?
How do I bleed the air out of my hot tub line?
Where is the flow switch on a hot tub?
The flow switch is located behind the outside walls of the spa and connected to the plastic piping.
David Nilsen is the former editor of Fourth & Sycamore. He is a member of the National Book Critics Circle. You can find more of his writing on his website at davidnilsenwriter.com and follow him on Twitter as @NilsenDavid.